- Jd 170 Lawn Mower Deck Manual Review
- Jd 170 Lawn Mower Deck Manual Download
- John Deere 170 Deck Parts
- Jd 170 Lawn Mower Deck Manual Diagram
Service 48 & 54 Inch Mower Deck
TRACTORS & MOWERS; Lawn Tractors; Utility Tractors (22.4-140 Engine HP) Specialty Tractors (75-155 Engine HP). 48' Mower Deck. E170 Lawn Tractor. 48' Mower Deck. Yearly Maintenance Kits. Home Maintenance Kit. Part Number AUC13707. Available to buy on JohnDeereStore.com Shop This Website. Maintenance Parts. 1 - John Deere Easy Change™ Oil. John Deere Lawn Mower Decks and Related Parts. John Deere is a manufacturer of tractors that are designed to deal with landscaping and yard maintenance projects of all sizes, whether residential or commercial. That means the company has a large selection of mower decks that can handle all sorts of thick vegetation and bumpy terrain. 38-inch Mower Deck Parts for 170. Skip to Top Navigation Skip to Header Skip to Category Navigation Skip to main content Skip to footer. John Deere Lawn Tractor.
Avoid Injury From Contacting Blades
MIF
c CAUTION: Avoid injury! To avoid injury, before you clean, adjust, or service mower: · STOP the engine. · LOCK the park brake. · DISENGAGE PTO to stop mower blades. · Remove the key. · Wait for mower blades to STOP. · Keep hands, feet and clothing away from mower deck when engine is running. · DISENGAGE PTO to stop mower blades when mower deck is raised. |
Grease
Use the following grease based on the air temperature range. Operating outside of the recommended grease air temperature range may cause premature failures.
IMPORTANT: Avoid damage! ONLY use a quality grease in this application. DO NOT mix any other greases in this application. DO NOT use any BIO-GREASE in this application. |
The following John Deere grease is preferred: Aperture free trial mac.
· TY6341 Multi-Purpose Super Duty High-Temperature EP POLYUREA Grease. NLGI Grade 2.
Other greases may be used if above preferred John Deere grease is not available, provided they meet the following specification:
· John Deere Standard JDM J13E4, NLGI Grade 2.
M58275
Mower Deck Gearbox Oil
Use the appropriate oil viscosity based on the air temperature ranges. Operating outside of these recommended oil air temperature ranges may cause premature gear case failure.
IMPORTANT: Avoid damage! ONLY use a quality oil in this gear case. DO NOT mix any other oils in this gear case. DO NOT use BIO-HY-GARD® in this gear case. |
The following John Deere gear case oil is PREFERRED:
· GL-5 GEAR LUBRICANT®-SAE 80W-90.
The following John Deere gear case oil is also recommended if above preferred oil is not available:
· GL-5 GEAR LUBRICANT®-SAE 85W-140.
Other gear case oils may be used if above recommended John Deere gear case oils are not available, provided they meet the following specification:
· API Service Classification GL-5.
M58275
Checking The Mower Gearbox Oil Level
1. Lower deck, stop the engine. Wait until the gearbox is cool.
2. Remove the check plug (A) from either side of the gearbox.
M73427
3. Oil should drain from the plug hole.
4. If not, pour or squirt oil through the check plug hole until the oil runs out of the hole.
5. Install plug. Wipe up any spilled oil.
Checking The PTO Gearbox Oil Level
1. STOP the engine.
M73459
2. Lift the seat to the second position.
3. Remove the check plug (A). Oil should flow from the plug hole.
4. If not squirt oil through the check plug hole, OR remove the fill plug (B) and squirt oil through the fill plug hole.
Jd 170 Lawn Mower Deck Manual Review
Changing The Mower Deck Gearbox Oil
1. STOP the engine. Wait until the gearbox is cool.
2. Lift the seat platform to the highest position.
3. Remove the driveline coupler from the vehicle's PTO gearbox shaft.
4. Remove the three mower deck belt shields. Use a spring puller to remove the end of the mower belt tension spring from its bracket.
5. Remove the two cap screws (A) from in front of the gearbox.
M73445
6. Remove the two bolts (B) and spacers from the rear of the gearbox.
7. Remove the gearbox and driveline from the belt and the mower.
8. Remove a check plug (C) from either side of the gearbox.
9. Turn the gearbox on it's side to drain it. After the oil has drained, turn the gearbox right side up.
M73445
10. Pour or squirt oil through the fill plug hole until the oil runs out of the check plug hole.
11. Install the plugs in the gearbox.
12. Install the gearbox on the mower. Install the belt on the gearbox sheave as you install the gearbox.
13. Tighten the cap screws and bolts to 70 N·m (50 lb-ft).
14. Connect the coupler to the vehicle gearbox shaft.
15. Use a spring puller to install the end of the spring in its bracket.
16. Install the belt shields.
17. Lower the seat.
Lubricating The Caster Wheel Bearings And Spindles
Lubricate the wheel bearings and spindle bushings on each front caster wheel assembly, using recommended John Deere Grease.
M73423
Lubricating The Mower Deck Spindles
Lubricate the three mower deck spindles using recommended John Deere Grease.
M56999
M57000
Lubricating The Gauge Wheel
Lubricate the gauge wheel axle using recommended John Deere Grease.
M73422
Lubricating The Crank Bushing
Lubricate the crank bushing grease fitting using recommended John Deere Grease.
M73424
Lubricating The Driveline U-joints And Spline
Lubricate the three grease fittings on the driveline using recommended John Deere Grease.
M73425
Removing And Installing The Belt Shields
c CAUTION: Avoid injury! Do not operate the mower without the belt shields. If you put your hand or foot between the moving belt and a sheave, the belt and sheave can tear your hand or foot off. The moving belt and sheaves can also throw debris that could injure your eyes or other parts of your body. |
M73419
1. To remove the shields, open the three latches shown.
2. Remove the center shield first, then the other two shields.
3. Install the outer shields first, then the center shield.
Removing The Mower Belt
c CAUTION: Avoid injury! Before you change belt, STOP engine. LOCK park brake. |
1. Remove the three belt shields.
2. Lower the mower all the way by turning the crank on the front of the mower.
3. Use a spring puller to remove the end of the spring (A) from the mower bracket.
M73341
4. Loosen the two cap screws (B) in front of the gearbox several turns.
M73386
5. Remove the two bolts (C) and the two spacers from the rear of the gearbox.
M73386
6. Use a bar to lift and hold up the rear of the gearbox.
7. Remove the belt from under the gearbox. Lower the gearbox.
8. Remove the belt from the other sheaves and discard it.
Installing Mower Belt
To install a new belt:
M57013
1. Use a bar to lift and hold up the rear of the gearbox.
2. Install the new belt on the sheave that is under the gearbox.
3. Lower the gearbox.
4. Use the picture at the right to help you install the belt on the other sheaves. Do not twist the belt.
Jd 170 Lawn Mower Deck Manual Download
5. Install the two bolts and spacers (A) at the rear of the gearbox.
M73386
6. Tighten the two bolts to 70 N·m (50 lb-ft).
7. Tighten the two cap screws (B) in front of the gearbox.
M73386
8. Use a spring puller to install the end of the spring (C) in the bracket.
M73341
9. Install the three belt shields.
Checking The Blades
c CAUTION: Avoid injury! The blades may be sharp. To help prevent injury when you handle the blades, wear heavy gloves orwrap the end of the blade with a rag. |
To check and remove a blade:
M73456
1. Put blocks in front of the mower.
2. Start the engine.
3. Pull up the attachment lift lever to raise the mower deck as high as it will go.
4. Hold the lift lever up and drive the Front Mower slowly forward until you can lower the deck onto the blocks.
5. Release the Lift Lever to lower the mower onto the blocks.
6. Stop the engine. Lock the park brake.
c CAUTION: Avoid injury! Do not work under a raised mower unless it is safely supported. |
7. Check the blades for damage and sharpness.
8. Replace blade(s) if damaged.
9. Sharpen dull blade(s). See 'Sharpening Blades' in this section.
10. To remove a blade, turn the bolt (A) counterclockwise. Fortigate vm trial license key.
Replacing The Rollers
1. Turn the crank to raise the mower as high as it will go.
M73436
2. Remove the lock nut (A).
3. Pull the shaft out and remove the roller.
4. Install the new roller on the shaft.
5. Install and tighten the lock nut.
Sharpening Blades
c CAUTION: Avoid injury! The blades may be sharp. To help prevent injury when you handle the blades, wear heavy gloves or wrap the end of the blade with a rag. Always wear gloves and goggles when sharpening, balancing or installing mower blades. |
John Deere 170 Deck Parts
1. Sharpen blades with grinder, hand file or electric blade sharpener.
MIF
2. Keep original bevel (A) when you grind. Blade should have 0.40 mm (1/64 in.) cutting edge (B).
3. Balance the blade. (See 'Balancing And Installing The Blades' in this section.)
Balancing And Installing The Blades
Jd 170 Lawn Mower Deck Manual Diagram
c CAUTION: Avoid injury! The blades may be sharp. To help prevent injury when you handle the blades, wear heavy gloves or wrap the end of the blade with a rag. |
IMPORTANT: Avoid damage! If you do not balance a blade, it may vibrate too much. |
1. To balance a blade:
· Clean the blade.
· Put the blade on a nail in a vise or wall. The heavy end of the blade will drop. Grind the bevel of the heavy end. Do not change the bevel.
2. Fasten blades with washers and bolts. The cup-side of the washer must be against the blade. Tighten bolts to 68-75 N·m (45-55 lb-ft).
M61524